3.6*10mm 玻璃管快断保险丝------- VDE UR CQC

产品信息
产品类别:玻璃管保险丝
关键词:保险丝,保险丝座,汽车保险丝,汽车保险丝座,温度保险丝,温控开关,电流保险丝,车用保险丝,车用保险丝座,热敏电阻,压敏电阻,过载保护器,自恢复保险丝,贴片保险丝,高压保险丝
点击率:
发布时间:2019-07-02 10:23:05
全国服务热线:13549460265
产品详情
3.6*10mm 玻璃管快断保险丝------- VDE UR CQC
 
1.規格型號和安規認證
MODEL  NUMBER  AND  SAFETY  CERTIFICATION
  • 品名規格:系列號+額定電流+額定電壓+認證符號
   Model  Number:  Part  Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
3GFV      1A     250V                      1)系列號  Part  Number
                                                     2)額定電流  Rated  Current
1)          2)    3)                       3)額定電壓  Rated  Voltage
1-2 額定電流和額定電壓
Rated Current  And  Voltage
額定電流: 100mA~6.3A
Rated Current: 100mA~6.3A
額定電壓:250V AC
Rated  Voltage:250V AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格:特性符號+額定電流+額定電壓
Specification:Characteristic  Symbol+Rated Voltage
   100mA~800mA : _mA250V    1A~6.3A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals  
 
100mA~6.3A: 


 
注意:對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
 
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖(單位:mm)
Outline Drawing and Dimensions(Unit:mm)
 



3-2結構
Structure
編號
No.
元件
Component
材質
Material
數量
Quantity
(1) 熔絲
Wire
合金
Alloy
1
(2) 銅帽
Cap
黃銅鍍鎳
Brass with mickel plated
2
(3) 本體
Body
玻璃管
Glasses tube
1
(4) 引線
Lead
鍍錫銅線
Tinned Copper wire
2
 
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀:不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀:帶腳的保險絲
Configuration:Axial Leaded Fuse.
 
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力,持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
 
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性:
Pre-Arcing Time/Current Characteristic
 
a、Breaking capacity(分断能力)(Time Lag and Fast Acting)
50A/3 250V AC
b、Electrical characteristics
Fast Acting
 % of Ampere  Opening Rating Time
150% 60 minutes, Minimum
210% 30 minutes, Maximum
275% 10 msec., Min.; 3 sec. Max.
400%  3 msec., Min.; .3 sec. Max.
1000%  20 msec, Max
 
c、Temperature character
    When 100% of rating the temperature rise doesn’t exceed 75℃.
d、ORDERING INFORMATION:
Catalog Number Ampere Rating Voltage Rating Nominal Resistance Cold mOhms Nominal Melting i2tA2Sec. Agency Approvals
VDE UR CQC
3GFV- .250  250mA  250V  0.406  440  × × ×
3GFV- .315  315mA  0.286  400  × × ×
3GFV- .400  400mA  0.220  370  × × ×
3GFV- .500  500mA  0.115  350  × × ×
3GFV- .630  630mA  0.100  320  × × ×
3GFV- .800  800mA  0.085  300  × × ×
3GFV- 001  1A  0.068  280  × × ×
3GFV- 1.25  1.2  0.052  280  × × ×
3GFV- 1.60  1.6A  0.042  250  × × ×
3GFV- 002  2A  0.032  240  × × ×
3GFV- 2.50  2.  0.021  200  × × ×
3GFV- 3.15  3.1  0.017  180  × × ×
3GFV- 004  4A  0.013  160  × × ×
3GFV- 005    0.010  150  × × ×
3GFV- 6.30  6.3A  0.007  150  × × ×
 
 
Average Time Current Curves


7.環境特性
 ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍:-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度:+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下,相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
 
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度:260±5℃
Soldering Temperature:260±5℃
焊接時間:4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度:350±5℃
Soldering Temperature: 350±5℃
焊接時間:3 Sec. Max.
Soldering Time: 3 Sec. Max.
 
 
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管,烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度:不大於150℃  烘烤時間:50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
采购:3.6*10mm 玻璃管快断保险丝------- VDE UR CQC
  • *联系人:
  • *手机:
  • 公司名称:
  • 邮箱:
  • *采购意向:
  • *验证码:

 
在线客服
在线客服
在线客服
在线客服
在线客服
在线客服
13549460265
13549460265