6.35*32慢断 UL 保险丝 额定电流：100mA-30A 额定电压：125V/250V
发布时间：2019-07-02 09:07:31点击率：
| 6.35*32陶瓷管慢断保险丝------- UL CSA |
|
1.規格型號和安規認證
MODEL NUMBER AND SAFETY CERTIFICATION
例子[example]:
6CTU 20A 250V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 63mA~30A
Rated Current: 63mA~30A
額定電壓：125V/250V AC
Rated Voltage:125V/250V AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓
Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA250V 1A~30A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
63mA~30A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag )
b、Electrical characteristics(参照美标)
c、Temperature character
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
MODEL NUMBER AND SAFETY CERTIFICATION
- 品名規格：系列號+額定電流+額定電壓+認證符號
例子[example]:
6CTU 20A 250V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 63mA~30A
Rated Current: 63mA~30A
額定電壓：125V/250V AC
Rated Voltage:125V/250V AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓
Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA250V 1A~30A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
63mA~30A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
|
編號 No. |
元件 Component |
材質 Material |
數量 Quantity |
| (1) |
熔絲 Wire |
合金 Alloy |
1 |
| (2) |
銅帽 Cap |
黃銅鍍鎳 Brass with mickel plated |
2 |
| (3) |
本體 Body |
陶瓷管 CERAMIC Tube |
1 |
| (4) |
引線 Lead |
鍍錫銅線 Tinned Copper wire |
2 |
| (5) |
砂 Sand |
石英砂 Quartz sand |
1 |
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag )
| 10000A | 125V | AC |
| 50A | 250V | AC (less or 1A) |
| 100A | 250V | AC (1.1A—2) |
| 600A | 250V | AC (2—30A) |
| Rated current | 100% | 135% | 200% | |
| 63mA~30A | Mini | Max. | MIN. | Max. |
| 4 hours, | 1 hour | 5 sec. | 60 sec. | |
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
| Amp Code |
Ampere Rating (A) |
Voltage Rating (V) |
Nominal Cold Resistance (Ohms) |
Nominal Melting I2t (A2 sec) |
Agency Approvals | |
| UL | CSA | |||||
| 6CTU-.010 | 0.01 | 125/250 | 3324.8000 | 0.00148 | x | x |
| 6CTU-.031 | 0.031 | 125/250 | 332.5000 | 0.0110 | x | x |
| 6CTU-.062 | 0.062 | 125/250 | 91.7000 | 0.0276 | x | x |
| 6CTU-.100 | 0.1 | 125/250 | 33.5500 | 0.0870 | x | x |
| 6CTU-.125 | 0.125 | 125/250 | 22.4500 | 0.100 | x | x |
| 6CTU-.150 | 0.15 | 125/250 | 15.4500 | 0.143 | x | x |
| 6CTU-.175 | 0.175 | 125/250 | 8.9200 | 0.220 | x | x |
| 6CTU-.187 | 0.187 | 125/250 | 7.7250 | 0.230 | x | x |
| 6CTU-.200 | 0.2 | 125/250 | 6.7700 | 0.213 | x | x |
| 6CTU-.250 | 0.25 | 125/250 | 4.4300 | 0.432 | x | x |
| 6CTU-.300 | 0.3 | 125/250 | 3.2200 | 0.690 | x | x |
| 6CTU-.375 | 0.375 | 125/250 | 2.1550 | 1.20 | x | x |
| 6CTU-.400 | 0.4 | 125/250 | 1.9350 | 1.33 | x | x |
| 6CTU-.500 | 0.5 | 125/250 | 1.3000 | 2.50 | x | x |
| 6CTU-.600 | 0.6 | 125/250 | 0.9495 | 3.90 | x | x |
| 6CTU-.700 | 0.7 | 125/250 | 0.7215 | 6.42 | x | x |
| 6CTU-.750 | 0.75 | 125/250 | 0.6410 | 7.00 | x | x |
| 6CTU-.800 | 0.8 | 125/250 | 0.5725 | 8.20 | x | x |
| 6CTU-001. | 1 | 125/250 | 0.3890 | 16.3 | x | x |
| 6CTU-1.25 | 1.25 | 125/250 | 0.2680 | 24.0 | x | x |
| 6CTU-01.5 | 1.5 | 125/250 | 0.1975 | 40.1 | x | x |
| 6CTU-01.6 | 1.6 | 125/250 | 0.1760 | 45.0 | x | x |
| 6CTU-002. | 2 | 125/250 | 0.1210 | 80.0 | x | x |
| 6CTU-02.5 | 2.5 | 125/250 | 0.0835 | 136.0 | x | x |
| 6CTU-003. | 3 | 125/250 | 0.0605 | 200.0 | x | x |
| 6CTU-004. | 4 | 125/250 | 0.0761 | 9.71 | x | x |
| 6CTU-005. | 5 | 125/250 | 0.0522 | 25.0 | x | x |
| 6CTU-006 | 6 | 125/250 | 0.0346 | 60.4 | x | x |
| 6CTU-007. | 7 | 125/250 | 0.0227 | 47.3 | x | x |
| 6CTU-008. | 8 | 125/250 | 0.0193 | 67.1 | x | x |
| 6CTU-010. | 10 | 125/250 | 0.0132 | 137 | x | x |
| 6CTU-012. | 12 | 125/250 | 0.0067 | 129 | x | x |
| 6CTU-015. | 15 | 125/250 | 0.0050 | 245 | x | x |
| 6CTU-020. | 20 | 125/250 | 0.0034 | 575 | x | x |
| 6CTU-025. | 25 | 125/250 | 0.0024 | 1030 | x | x |
| 6CTU-030. | 30 | 250 | 0.0019 | 1690 | x | x |
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.