5*20 陶瓷高压保险丝 5CH-500V/600V/1000V/3000V
发布时间：2019-07-02 09:07:55点击率：
| 5*20 陶瓷高压保险丝 5CH-500V/600V/1000V/3000V |
|
1.規格型號和安規認證
MODEL NUMBER AND SAFETY CERTIFICATION
例子[example]:
5CH 1A 1000V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 63mA~1
Rated Current: 63mA~1
額定電壓:500V/600V/1000V AC/DC
Rated Voltage: 500V/600V/1000V AC/DC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓
Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA500V/600V/1KV 1A~1:_A500V/600V/1KV
Trade mark:The Manufacture’s Logo+Part Number+Approvals
63mA~1:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
b、Electrical characteristics
Fast Acting
美标（UL）
c、Temperature character
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
7.環境特性
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
MODEL NUMBER AND SAFETY CERTIFICATION
- 品名規格：系列號+額定電流+額定電壓+認證符號
例子[example]:
5CH 1A 1000V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 63mA~1
Rated Current: 63mA~1
額定電壓:500V/600V/1000V AC/DC
Rated Voltage: 500V/600V/1000V AC/DC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓
Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA500V/600V/1KV 1A~1:_A500V/600V/1KV
Trade mark:The Manufacture’s Logo+Part Number+Approvals
63mA~1:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
|
編號 No. |
元件 Component |
材質 Material |
數量 Quantity |
| (1) |
熔絲 Wire |
合金 Alloy |
1 |
| (2) |
銅帽 Cap |
黃銅鍍鎳 Brass with mickel plated |
2 |
| (3) |
本體 Body |
玻璃管 CERAMIC Tube |
1 |
| (4) |
引線 Lead |
鍍錫銅線 Tinned Copper wire |
2 |
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
| 15000A | 500/600V/1KV/3KV | AC/DC |
b、Electrical characteristics
Time Lag（国标、欧标CCC/VDE）
| RATED CURRENT | 2.1IN | 2.75IN | 4IN | 10IN | |||
|
32mA to 100mA |
Max. | Min. | Max. | Min. | Max. | Min. | Max. |
| 30 min. | 1S | 80S | 95mS | 5S | 10mS | 100mS | |
| 大于100mA | 30 min. | 1S | 80S | 150mS | 5S | 20mS | 100mS |
| RATED CURRET | 2.1IN | 2.75IN | 4IN | 10IN | ||
|
大于50mA |
Max. | Min. | Max. | Min. | Max. | Max. |
| 30 min | 10ms | 2S | 3ms | 300ms | 20ms | |
| Rated current | 1IN | 1.35IN | 2IN |
| MIN | MAX | MAX | |
| 63mA~1 | 4Hrs | 1hr | 5Sec |
c、Temperature character
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
| Catalogue number | Rated current | Voltage | 参照美标、欧标 |
| 5CFP/5CTP | 63mA~1 | 500/600V/1KV |
7.環境特性
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.